How to Cut a Picture Frame With a Miter Saw
Here's how to cut a picture frame with a miter saw: cut four pieces with a 45 degree miter on each end, keep the face of the frame up, and measure each piece for its position. Then assemble the corners around the picture, glue, and clamp.
On this page (9 sections)
- What do you need before cutting a picture frame?
- How do you plan the four frame pieces?
- How do you set a miter saw for 45 degree cuts?
- How do you cut the first miter and then the matching length?
- How do you avoid gaps at the corners?
- Should you cut the frame oversize and trim it later?
- How do you choose the saw for frame work?
- What fastening holds the mitered corners together?
- How should you finish the frame once it's together?
Here's how to cut a picture frame with a miter saw: cut four pieces with a 45 degree miter on each end, keep the face of the frame up, and measure each piece for its position. Then assemble the corners around the picture, glue, and clamp.
The saw doesn't do the tricky part. Your measuring and your corner order do.
Once those are set, a miter saw makes short work of clean 45 degree ends.
What do you need before cutting a picture frame?
You need frame stock, a fine-tooth blade, a 45 degree miter setting, a stop block, and clamps for the four corners. Add wood glue and a square for checking the joints.
Pick stock that's wide enough for the picture plus any mat. A flat stick with a rabbet cut on the back already holds the glass and photo.
Check the saw's miter scale first. Set it to 45 degrees and lock it, then confirm the angle at the blade with a speed square if you can.
A finer blade gives cleaner end grain. The Freud LU91M010 is a 10 inch, 60 tooth thin kerf blade with alternating top bevel teeth and a 5/8 inch arbor, made for sliding compound miter saws.

A 60 tooth crosscut blade that leaves clean end grain on frame corners.
See it on AmazonThin kerf removes less wood, so the cut loads the motor less. That suits a home shop saw that isn't the biggest in the lineup.
Two more details in the blade specs matter for frames. The kerf is .090 inch, which means each pass takes a narrow slice and leaves more of your stock intact.
The teeth also carry a negative hook angle of 5 degrees, which pushes the work down against the fence instead of grabbing it, so a narrow frame stick stays put through the cut.
How do you plan the four frame pieces?
Cut two long sides first, then use them to set the two short sides. That way the pairs match and the frame stays square.
The outside length of each piece runs from the tip of one miter to the tip of the other. Inside length is what the picture sees.
Decide which face shows and mark it. Every cut should keep that face up, so any chip-out happens on the back.
Wait to cut anything until you've measured the photo, the glass, and the mat together. A frame that fits a bare print won't hold a matted one.
Write the four lengths on the stock before you start cutting. Labeling each piece by position, rather than by size, is what stops you from swapping a long side with a short one after the miters are already cut.
How do you set a miter saw for 45 degree cuts?
Set the miter table to 45 degrees and keep the blade vertical. Leave the bevel at 0 degrees, because a picture frame is a flat miter, not a slanted one.
Push the miter lock knob tight and test it by swinging the blade. Loose tables creep between cuts.
Lock the saw head down and hold the stock against the fence with the back face flat. Then bring the blade down slowly.
The Makita LS1040 has 9 positive stops, including 45 degrees left and right, plus miter travel from 45 left to 52 right.

Positive stops at 45 degrees on both sides make repeat frame cuts quick to set.
See it on AmazonA stop set on each side also lets you cut left and right miters without re-checking the scale every time. Its direct drive motor runs at 4,600 RPM with no belt to slip, and the saw weighs about 27 pounds, so it's easy to carry to a bench for a small job.
How do you check that the setting is truly 45?
Cut two scrap pieces at the setting and stand them on edge as a corner. Any light showing at the point means the table is off, so nudge the lock and try again.
A framing square laid along the outside edges of the dry fit tells you the same thing. If the corner opens at the tip and closes at the heel, the angle is under 45.
If it's the other way, the angle is over.
How do you cut the first miter and then the matching length?
Square one end of the stock, cut the first 45, then measure from the tip of that miter and cut the second end at the opposite angle. That's how two identical sides come out.
Start with the stock flat. Trim a square end so you have a clean reference, then set 45 and cut the first corner.
For the matching end, swing the table the other way, or flip the stock if the saw only miters one way. A saw with both left and right miter settings is easier here.
Measure from the longest point of the miter to where the second tip should land. Mark the face side, not the back.
The Skil MS6305-00 miter table turns up to 50 degrees left and right with 11 positive stops, and its 15 amp motor runs at 4,800 RPM.

Wide miter travel both ways for cutting left and right frame corners without re-rigging.
See it on AmazonThe LED shadow line helps you line the blade up with a pencil mark on darker frame stock. On a narrow stick, a line of shadow against the teeth is easier to follow than a chalk mark that the blade dust hides.
How do you avoid gaps at the corners?
Cut both matching sides from one stop setting, and check square before gluing. Most open corners come from unequal lengths, not from the saw angle.
Use a stop block on the fence so the second side lands exactly like the first. Set it once, cut one piece, test the fit, then cut the mate.
Mark each piece by position, long left, long right, short top, short bottom. That keeps the angle direction right on every end.
Cut test pieces in scrap first if the stock is expensive or the saw was moved. Two scrap miters closed against a square tell you plenty.
Clamp the pieces dry before glue. Any gap you can see dry will only open more when the glue swells the wood.
Keep pressure toward the fence and down on the table as the blade enters. A stick that shifts halfway down the cut leaves a miter that looks right but doesn't mate, and that shows up only when you clamp the frame.
How do you cut the short sides once the long ones match?
Lay the two long sides flat with their miters facing out, then measure the gap between the two inside faces at the top and at the bottom. That gap is the inside length of each short side.
Cut both shorts to that number from the same stop setting.
Should you cut the frame oversize and trim it later?
Yes, cut slightly long and trim as a set. A little extra on both sides is easy to take off and impossible to add back.
Leave a small amount on each side of the opening when you mark the pieces. Assemble the dry frame, slip the glass and photo in, and see what needs trimming.
If the corners won't close, re-cut both ends of one piece only, never one end alone. Matching pairs keep the frame square.
Trim across the saw table with the same miter setting, so the tips stay at 45.
How do you choose the saw for frame work?
Any miter saw that holds a solid 45 degree setting will cut picture frames. The size and motor matter less than a locked table and a sharp fine-tooth blade.
The question of what a miter saw is used for covers the basic cuts. Frame work is one of them, and it barely needs the saw's big capacity.
A sliding saw or dual bevel model gives extra reach and speed. If you're still comparing, miter saw vs compound miter saw explains which features change the work and which don't.
Frame stock is usually narrow, so a small saw handles it. For thicker stock, check whether a miter saw can cut a 4x4, because capacity limits show up long before frame widths do.
Soft metal frame channel is a different job. Read whether a miter saw can cut aluminum before you put metal near the blade.
What fastening holds the mitered corners together?
Glue and clamp first, then add a fastener on the back. Glue gives the strongest hold, and the fastener keeps the corner from sliding while it dries.
Painters tape around all four corners works as a clamp on small frames. Stretch it tight and the corners pull closed as the glue sets.
Corrugated fasteners or V-nails fired into the back hold the joint once the glue has cured. A staple across the back corner also works.
Check the diagonal measurements with a tape. If they match, the frame is square.
How should you finish the frame once it's together?
Fill any visible corner gap, sand flush, and finish before adding the photo. The frame is easiest to handle while it's still empty.
Sand the joints lightly with the grain, then ease the edges. Wipe off dust before stain or paint.
Set the glass, the photo, and a backing board, then hold the back with points or brads. Add a hanger rated for the frame weight.
When you build a second one, plan the cuts and add-ons around the same stop block setting. The measuring routine should be the whole lesson.
To cut a picture frame with a miter saw, the fixture is the stop and the eye on the mark. Set a true 45, keep matching sides equal, and glue the corners closed.
Frequently asked questions
Do I need a compound miter saw to cut a picture frame?
No. A plain miter saw makes every frame cut you need, because the 45 degree miters come from turning the table, not from tilting the blade.
A compound saw is handy if you also build deep shadow boxes with slanted sides.
Can I cut a picture frame on a miter saw without a stop block?
Yes, but you'll measure and mark each piece by hand, and four small differences in length show up as open corners. A stop block against the fence lets you set one length and cut two matching pieces, which is what keeps opposite sides equal.
Which blade leaves the cleanest frame corners?
A fine-tooth crosscut blade, around 60 teeth on a 10 inch saw, gives the smoothest end grain for a glued miter. A coarse combination blade tends to tear the tips of the cut, and torn fibers make a visible gap once the joint is closed.
How much longer should the frame pieces be than the photo?
Add the size of the rabbet on each side, which is the ledge the picture sits on, plus room for a mat. A frame built for an 8 by 10 print with a 1/4 inch rabbet needs an opening close to that size, so cut the outside length after checking the rabbet depth.
About this guide: Our look at cutting a picture frame on a miter saw draws on maker specs, materials and what owners report. See how we research.



